In the IT industry, the Cisco Certified Network Associate (CCNA) 200-301 is one of the most popular entry-level certifications for network engineers. Many candidates face challenges during preparation due to scattered knowledge points and a lack of systematic practice. To help everyone prepare more efficiently, I will share 15 of the latest CCNA 200-301 practice questions for free and recommend visiting https://www.leads4pass.com/200-301.html to download the complete 1629 Q&A dumps to help you pass the exam in one attempt.
Latest Changes to the CCNA 200-301 Exam in 2025
The exam syllabus for 2025 remains stable, but Cisco places greater emphasis on network security and automation. Candidates are expected not only to master routing and switching fundamentals but also to have skills in using tools like Python and APIs.
You can find an introduction and other basic information about the CCNA 200-301 exam in my previously published CCNA 200-301 article, or you can visit the official website for a more detailed introduction.
Why is Practicing CCNA 200-301 Practice Questions Important?
1.Improve Speed and Accuracy in Answering Questions
The actual exam has limited time, and consistent practice with questions can enhance your problem-solving speed.
2.Understand the Distribution of Exam Knowledge Points
Practice questions help candidates become familiar with question types in advance and identify weak areas for review.
3.Develop Test-Taking Mindset and Practical Skills
Training with practice questions builds a habit of quickly analyzing complex network issues, strengthening your ability to handle real exam scenarios.
Free Access: 15 Latest CCNA 200-301 Practice Questions
I will provide 15 carefully selected CCNA 200-301 practice questions in this article to help you assess your learning progress. These questions cover common exam topics, such as:
- Network Fundamentals and Configuration
- IP Addressing and Subnetting
- Network Security and Access Control
- Wireless Network Principles
- Automation and Scripting Basics
Question 1:
DRAG DROP
Drag and drop the HTTP methods used with REST-based APIs from the left onto the descriptions on the right.
Select and Place:
Correct Answer:
Question 2:
Refer to the exhibit.
What is the next hop address for traffic that is destined to host 10.0.1.5?
A. Loopback 0
B. 10.0.1.4
C. 10.0.1.50
D. 10.0.1.3
Correct Answer: C
/32 prefix represents a host, and this is the highest you can get with ipv4. The next hop is 10.0.1.50 as you can see where it says \’via 10.0.1.50\’.
Question 3:
What are two functions of a server on a network? (Choose two)
A. achieves redundancy by exclusively using virtual server clustering
B. runs applications that send and retrieve data for workstations that make requests
C. handles requests from multiple workstations at the same time
D. runs the same operating system in order to communicate with other servers
E. housed solely in a data center that is dedicated to a single client
Correct Answer: BC
Question 4:
Guidelines
This is a lab item in which tasks will be performed on virtual devices
1.
Refer to the Tasks tab to view the tasks for this lab item.
2.
Refer to the Topology tab to access the device console(s) and perform the tasks.
3.
Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
4.
All necessary preconfigurations have been applied.
5.
Do not change the enable password or hostname for any device.
6.
Save your configurations to NVRAM before moving to the next item.
7.
Click Next at the bottom of the screen to submit this lab and move to the next question.
8.
When Next is clicked the lab closes and cannot be reopened.
Three switches must be configured for Layer 2 connectivity. The company requires only the designated VLANs to be configured on their respective switches and permitted across any links between switches for security purposes. Do not modify or delete VTP configurations.
The network needs two user-defined VLANs configured:
1.
VLAN 202: MARKETING
2.
VLAN 303: FINANCE
1.
Configure the VLANs on the designated switches and assign them as access ports to the interfaces connected to the PCs.
2.
Configure the e0/2 interfaces on Sw1 and Sw2 as 802.1q trunks with only the required VLANs permitted.
3.
Configure the e0/3 interfaces on Sw2 and Sw3 as 802.1q trunks with only the required VLANs permitted.
A. Check the below
B. Place Holder
C. Place Holder
D. Place Holder
Correct Answer: A
SW1):
vlan 303 name FINANCE vlan 202 name MARKETING
int e0/1 switchport mode access switchport access vlan 303
int e0/2 switchport mode trunk switchport encapsulation dot1q switchport trunk allowed vlan 303, 202
SW2):
vlan 303 name FINANCE vlan 202 name MARKETING
int e0/1 switchport mode access switchport access vlan 202
int e0/2 switchport mode trunk switchport encapsulation dot1q switchport trunk allowed vlan 303, 202
int e0/3 switchport mode trunk switchport encapsulation dot1q switchport access vlan 303, 202
SW3):
vlan 303 name FINANCE vlan 202 name MARKETING
int e0/0 switchport mode access switchport access vlan 202
int e0/1 switchport mode access switchport access vlan 303
int e0/3 switchport mode trunk switchport encapsulation dot1q switchport trunk allowed vlan 303, 202
Question 5:
Which type of ipv6 address is publicly routable in the same way as ipv4 public addresses?
A. multicast
B. unique local
C. link-local
D. global unicast
Correct Answer: D
The type of IPv6 address that is publicly routable in the same way as IPv4 public addresses is a global unicast address.
Global unicast addresses are unique, globally reachable addresses that are assigned to devices that need to communicate with other devices over the Internet.
They are similar to IPv4 public addresses in that they can be used to reach devices on other networks, but they are structured differently and use a different address space.
Global unicast addresses are identified by the prefix “2000::/3” and are assigned to devices by their network administrator or by an Internet service provider (ISP).
They are used for communication between devices on different networks, such as between a device on a LAN and a device on the Internet.
It\’s important to note that global unicast addresses are not the same as link-local addresses, which are used for communication within a single network segment or link and are not intended to be routable over the Internet.
Link-local addresses are identified by the prefix “FE80::/10” and are automatically generated by the device when it is connected to a network.
Question 6:
Which configuration is needed to generate an RSA key for SSH on a router?
A. Configure the version of SSH
B. Configure VTY access.
C. Create a user with a password.
D. Assign a DNS domain name
Correct Answer: D
Question 7:
Guidelines
This is a lab item in which tasks will be performed on virtual devices
1.
Refer to the Tasks tab to view the tasks for this lab item.
2.
Refer to the Topology tab to access the device console(s) and perform the tasks
3.
Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window
4.
All necessary preconfigurations have been applied
5.
Do not change the enable password or hostname for any device
6.
Save your configurations to NVRAM before moving to the next item
7.
Click Next at the bottom of the screen to submit this lab and move to the next question
8.
When Next is clicked the lab closes and cannot be reopened
Topology
Tasks
Physical connectivity is implemented between the two Layer 2 switches, and the network connectivity between them must be configured.
1.
Configure an LACP EtherChannel and number it as 44; configure it between switches SW1 and SW2 using interfaces Ethemet0/0 and Ethernet0/1 on both sides. The LACP mode must match on both ends.
2.
Configure the EtherChannel as a trunk link.
3.
Configure the trunk link with 802.1q tags.
4.
Configure VLAN \’MONITORING\’ as the untagged VLAN of the EtherChannel.
A. Check the below
B. Place Holder
C. Place Holder
D. Place Holder
Correct Answer: A
S1 interface range eth0/0-1 shut channel-group 44 mode active no shut interface port-channel 44 switchport mode trunk switchport trunk encapsulation dot1q switchport trunk native vlan 746
S2 interface range eth0/0-1 shut channel-group 44 mode active no shut interface port-channel 44 switchport mode trunk switchport trunk encapsulation dot1q switchport trunk native vlan 746
First before you create an etherchannel you have to shutdown the ports you going to create it on. Second when you go into the etherchannel interface to create the trunk you have to type the command interface port-channel 44.
Lastly you have to you have issue the no shutdown command on the interface ranges on both switches at the end to bring them back up.
Question 8:
Refer to the exhibit. Web traffic is coming in from the WAN interface.
Which route takes precedence when the router is processing traffic destined for the LAN network at 10.0.10.0/24?
A. via next-hop 10.0.1.5
B. via next-hop 10 0 1.4
C. via next-hop 10.0 1.50
D. via next-hop 10.0 1 100
Correct Answer: A
Question 9:
DRAG DROP
Drag and drop the wireless architecture benefits from the left onto the architecture types on the right.
Select and Place:
Correct Answer:
Question 10:
What describes the operation of virtual machines?
A. Virtual machines are responsible for managing and allocating host hardware resources
B. In a virtual machine environment, physical servers must run one operating system at a time.
C. Virtual machines are the physical hardware that support a virtual environment.
D. Virtual machines are operating system instances that are decoupled from server hardware
Correct Answer: D
Question 11:
Refer to the exhibit.
A network engineer must provide configured IP addressing details to investigate a firewall rule Issue. Which subnet and mask Identify what is configured on the en0 interface?
A. 10.8.0.0/16
B. 10.8.64.0/18
C. 10.8.128.0/19
D. 10.8.138.0/24
Correct Answer: C
Question 12:
Refer to the exhibit.
All interfaces are in the same VLAN. All switches are configured with the default STP priorities. During the STP elections, which switch becomes the root bridge?
A. MDF-DC-1: 0d:E0:43:96:02:30
B. MDF-DC-2: 0d:0E:18:1B:05:97
C. MDF-DC-4: 0d:E0:19:A1:B3:19
D. MDF-DC-3: 0d:0E:18:2A:3C:9D
Correct Answer: B
Question 13:
Which interface is used to send traffic to the destination network?
A. G0/10
B. G0/24
C. G0/5
D. G0/1
Correct Answer: B
Question 14:
Which connection type is used when an engineer connects to an AP without a configured IP address or dial-up number to manage the device?
A. AUX
B. Ethernet
C. VIY
D. console
Correct Answer: D
Question 15:
Refer to the exhibit.
A network administrator assumes a task to complete the connectivity between PC A and the File Server. Switch A and Switch B have been partially configured with VLANs 10, 11, 12, and 13.
What is the next step in the configuration?
A. Add PDA to VLAN 10 and the File Server to VLAN 11 for VLAN segmentation
B. Add VLAN 13 to the trunk links on Switch A and Switch B for VLAN propagation
C. Add a router on a stick between Switch A and Switch B allowing for Inter VLAN routing
D. Add PC A to the same subnet as the File Server allowing for intra-VLAN communication
Correct Answer: B
How to Obtain the Complete 1629 Q&A dumps
Why Choose Leads4pass for Downloading the dumps?
Leads4pass is a well-known IT Dumps provider in the industry, offering a CCNA 200-301 dumps with a coverage rate of over 95%.
Update Frequency and Authority of the Leads4pass dumps
Leads4pass continuously updates its dumps to ensure high alignment with the actual exam, preventing candidates from wasting time on outdated materials.
How to Download the 1629 Q&A dumps (Detailed Steps)
- Visit Leads4pass.com
- Search for CCNA 200-301
- Choose between PDF or VCE practice formats
- Register and download to access the complete dumps
Effective Study Strategies for Preparing for the CCNA 200-301 Exam
Create a Structured Study Plan
It’s recommended that candidates study in phases: Fundamentals → Advanced Topics → Practice Exams → Final Sprint.
Combine Official Textbooks with Practice Questions
Cisco’s official textbooks are essential study materials, but pairing them with practice questions is key to mastering critical concepts.
Proper Use of Online Resources and Question Banks
Avoid rote memorization; instead, use question banks to understand the logic behind the knowledge points.
Frequently Asked Questions (FAQ)
Is the CCNA 200-301 Exam Difficult?
The exam is moderately difficult, requiring systematic review and extensive practice.
Are the 15 Free Practice Questions Enough for Exam Preparation?
They are not sufficient to cover all exam topics but can serve as a tool to assess your learning progress. It’s recommended to use them alongside a complete question bank.
Is the Leads4pass Question Bank Reliable?
Yes, the question bank provided by Leads4pass is highly similar to the actual exam and has a good reputation.
How Long Is the CCNA Certificate Valid?
The CCNA certificate is valid for 3 years, after which recertification is required.
How Similar Is the CCNA Question Bank to the Actual Exam?
The similarity is very high, especially with the latest question bank from Leads4pass.
What Types of Questions Are Included in the 1629 Q&A Question Bank?
It includes multiple-choice questions, drag-and-drop questions, and lab configuration questions, covering the core knowledge points of the CCNA exam.
Conclusion: Use the Right Resources to Easily Pass the CCNA 200-301 Exam
In summary, the free 15 practice questions can help you quickly assess your learning progress, while the complete 1629 Q&A question bank is the key weapon for passing the exam. If you plan to successfully obtain your CCNA certification in 2025, it’s recommended to start practicing now and visit Leads4pass to download the full question bank to give yourself an extra layer of assurance.
Comments are closed.